Buy ASTM A 36/A36M: SPECIFICATION FOR CARBON STRUCTURAL STEEL from SAI Global. Astm a36 – A36m – Download as PDF File .pdf), Text File .txt) or read online. ASTM A/AM Steel, Sheet and Strip, Heavy-Thickness Coils, Hot- Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy.
|Published (Last):||17 December 2013|
|PDF File Size:||16.64 Mb|
|ePub File Size:||18.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
C Yield point 32 ksi [ MPa] for plates over 8 in.
ASTM A36/ A36M
The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.
Heat analysis shall be used to 3a6m the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, and copper. DIN – Current edition approved March 1, Such operations include decoiling, leveling or straightening, hot-forming or cold-forming if applicablecutting to length, testing, inspection, conditioning, heat treatment if applicablepackaging, marking, loading for shipment, and certication. Such notes and footnotes, excluding those in tables and gures, do not contain any mandatory requirements.
See Appendix X3 of Speci? This standard has been approved for use by agencies of the Department of Ast. The heat analysis for manganese shall be determined and reported as described in the heat analysis section of Speci? Within the text, the SI units are shown in brackets.
ASTM A36/ A36M – AL-RASHED FASTENERS
Approved May 15, Chemical composition or mechanical properties, or both, may be different than speci? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
E For plates wider than 24 in. Single Heat Bundles S Additional requirements regarding astmm products produced from coil are described in Speci? This abstract is a brief summary of the referenced standard. Such requirements apply only when specified in the purchase order.
Materials and Manufacture 6. Standardized supplementary requirements for use at the option of the purchaser are listed in Speci?
Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements. Alternate Core Location S It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. Limitation on Astj or Capped Steel S Product ShapesA To 34 , incl 0.
Work Item s – proposed revisions of this standard. Within the text, the SI units are shown in brackets. A36 on Rimmed or Capped Steel S Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Structural products produced from coil means structural products that have been cut to individual lengths from a coil. Elongation in 8 in. The processor directly controls, or is responsible for, the operations involved in the processing a36n a coil into a nished structural product.
ASTM A36/A36M-08 Structural A-36 Steel
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. NOTE 1—For structural products produced from coil and furnished without heat treatment or with stress relieving only, two test results are to be reported for each qualifying coil. The values stated in each system are not exact equivalents; therefore, each system is to aatm used independently of the other, without combining values in any way. General Requirements for Delivery 4.
Originally approved in Charpy V-Notch Impact Test. B For wide ange shapes with ange thickness over 3 in. Such notes and footnotes, excluding those in tables and? The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way. A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
For each reduction of 0.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
D Elongation not s36m to be determined for oor plate.